Mazda 323
+ Introduction
+ Petrol engines
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and system of steering
+ Brake system
+ Wheels and tires, body, coloring of the car, care of the car
+ System of electric equipment
+ Heater, system of lighting, devices
- Governing bodies and methods of operation
Before landing in the car
Running in
Keys
Locks of doors
The uniform (central) locking device (if is available)
Protection against pranks of children (if is available, only on back doors)
The power window (if is available)
Back rotary glasses (on 3-door models)
Seats
Adjustment of height of a steering wheel (if is available)
Seat belts (if is available)
Door back/trunk lid
Fuelling
Mirrors
Luggage belts
Trunk lid (if is available)
Spare wheel
Dashboard
+ Steering wheel and gear shifting
+ Electric circuits
|
Seat belts (if is available) Seat belts with the automatic involving device
For decrease in danger to be traumatized at accident or emergency brake application all passengers have to be always fastened by the available seat belts. Forward belts with three points of fastening are equipped with the lock device. Thanks to belts with the involving device landing and disembarkation of passengers is facilitated and the comfort improves. With the big force of delay, for example, at sharp braking, belts are automatically blocked to protect passengers from injuries.
|
|
If at a pulling the belt was blocked, he needs to be moved away again before it can be extended at desirable length. |
|
|
Seat belts have to be replaced after each strong impact on them, for example, after accident. |
Seat belts of front seats
Fastening of belts
|
|
- Take the lock of a belt and a plug-in uvula.
- Slowly extend a belt.
- Implant a uvula into the belt lock that it was latched.
|
|
- Tighten the lower part of a belt as it is possible more deeply on hips that you in case of accident could not slip under a belt. Stretch a belt through a uvula, so that it adjoined to a body. Automatic equipment of retraction will automatically involve the weakened tape of a belt.
|
|
|
Never impose a belt near at hand, around a neck or on an internal shoulder, otherwise, protective influence significantly decreases. |
|
|
Removal of a seat belt
|
|
|
|
- For removal of a seat belt press the button on the belt lock.
|
|
|
Seat belts of a back seat (with the involving device)
|
|
Rules of the address same, as well as for forward seat belts. |
(without the involving device)
Type A
Fastening of seat belts
|
|
- Take the lock of a belt and a uvula.
- Implant a uvula into the belt lock that it was latched.
|
|
- Adjust if it is necessary, belt length. For this purpose you hold the regulator at right angle to a belt and pull it to extend a belt. If to pull for the weakened end of a belt, the belt will be truncated.
|
- Impose the lower part of a belt as it is possible more deeply on hips.
|
|
Suspension bracket of three-point seat belts
|
|
|
|
- Suspend a uvula on a hook of a cover of fastening of a belt if the belt is not used.
|
|
|
Type B
Fastening of seat belts
|
|
- Impose the lower part of a belt as it is possible more deeply on hips and adjust belt length. For this purpose you hold a belt uvula at right angle to a belt and pull it to extend a belt. If to pull for the weakened end of a belt, the belt will be shortened.
|
|
Removal of a seat belt
|
|
|
|
- For removal of a seat belt press the button on the belt lock.
|
|
|
Rules of the address and care of system of seat belts
For achievement of the maximum protective influence of system of seat belts observe, please, the next moments:
- Never to be fastened by one belt to two passengers.
- You watch that the tape of a belt was not twisted.
- You hold belts and other parts of system far away from sharp edges and objects which can damage.
- Check through equal intervals fabric of belts, locking details, points of fastening and other details of a belt for wear, damages and weak points. At once replace the damaged details.
- For cleaning of a belt use soft solutions of soap or soft detergents. It is not recommended to clear belts such chemicals as tetrachlormethane or gasoline, and also to bleach or tint belt fabric.
- On belts it should not be made any changes or additions.
- After use of a belt, it is necessary to be convinced that it was not hooked for control levers or other objects.
|
|
