For consolidation of the pallet of a case in workshops MAZDA No. 852777739 sealant is used, also similar sealant on a silicone basis can be used (for example, DOW CORNING Q3 - 7057).
Not to apply too much sealant, and in the field of oil channels to work especially carefully. Details have to be collected within 30 minutes after putting sealant. After this time sealant has to be removed and applied anew.
Removal
1 — a bolt, 50 Nanometers 2 — a fastening plate 3 — laying, always to replace 4 — a nut, 45 Nanometers 5 — a bolt, 50 Nanometers 6 — a reception pipe of the muffler 7 — a nut, 90 Nanometers 8 — laying, always to replace 9 — a rigidity element (On models with the case pallet from aluminum it is built in the pallet.) 10 — bolts of 50 Nanometers
11 — laying, always to replace 12 — the case pallet 13 — a bolt, 10 Nanometers 14 — a stopper of a masloslivny opening, 40 Nanometers 15 — laying, always to replace 16 — the mesh filter 17 — a support of bearings 18 — a bolt, 10 Nanometers 19 — a bolt, 20 Nanometers 20 — Laying, always to replace
PERFORMANCE ORDER
To disconnect a weight cable from the battery.
At the same time data from memory of malfunctions of the engine or a protective code of the radio receiver are erased. Before shutdown of the battery it is necessary to read instructions in the Section Removal also installation of the battery.
VZ, V6 (SOHC) from 9/89 g of the issue: To unscrew a rigidity element.
To unscrew bolts and nuts of fastening of the pallet of a case.
Steel pallet: For push-up of the pallet to install the screw-driver between a basic arm and the pallet.
The screw-driver cannot be installed between a support of bearings and the block of cylinders. Besides at removal of the pallet to watch that the sealing surfaces of the pallet and block of cylinders were not damaged.
Aluminum pallet: To chuck in the screw-driver the specified place between the pallet and the block of cylinders.
The screw-driver should not be installed on any other place as differently the sealing surfaces of the pallet of a case and the block of cylinders will be damaged.
To remove the case pallet.
If is available, to unscrew a support of bearings and to remove it.
Installation
PERFORMANCE ORDER
It is careful to exempt the sealing surfaces of the pallet of a case, a support of bearings and the block of cylinders from old consolidation by means of a triangular shaber and an edge of the razor.
To carefully wipe the block of cylinders, a case and the oil pump. Otherwise consolidation can be damaged by the following oil.
To wipe sealing surfaces on the case pallet, a support of bearings and the block of cylinders with solvent of fat and to dry up them. As a cleaner alcohol or acetone can be used.
It is impossible to apply the cleaners corroding varnish surfaces.
To apply on the shaded places sealant on a silicone basis (for example, DOW CORNING Q3 - 7057).
To apply sealant on a silicone basis (for example, DOW CORNING Q3 - 7057).
To establish a support of bearings and to tighten 20 Nanometers with effort.
To apply sealant on a silicone basis (for example, DOW CORNING Q3 - 7057) on laying and to establish laying.
Ledges on laying have to be turned outside, the ends have to adjoin purely.
To apply sealant on a silicone basis (for example, DOW CORNING Q3 - 7057).
Steel pallet
PERFORMANCE ORDER
To install the pallet and to evenly screw 10 Nanometers with effort.
To establish an element of rigidity and to screw fastening bolts with effort of 50 Nanometers.
Aluminum pallet: To install the pallet and to evenly tighten bolts - And - with effort of 10 Nanometers, bolts - In - with effort of 50 Nanometers.
To establish a reception pipe of the muffler.
To lower the car.
To fill in engine oil.
To connect a cable of mass of the battery.
If are available, to determine time on hours and to set a protective code of the radio receiver.
To make a trial trip, to check the level of oil and tightness of the pallet of a case, perhaps carefully to tighten bolts.
