Mazda 323

since 1985 release

Repair and operation of the car


Mazda 323

- Introduction
   About this Management
   Mazda-323 brand cars — the introduction
   Identification numbers of the car
   Acquisition of spare parts
   Technology of service, tools and equipment of a workplace
   Start of the engine from an auxiliary source
   Poddomkrachivaniye and towage
   Automobile chemicals, oils and lubricants
   Diagnostics of malfunctions
   Routine maintenance
   - Works on maintenance
      Oil replacement
      Replacement of an oil filter
      Replacement of a perepuskny oil filter
      Visual check on oil leak
      Check of level of engine oil
      Check of level of cooling liquid
      Replacement of cooling liquid
      Visual check of tightness of the cooling system
      Frost resistance check
      Adjustment of gaps of valves
      Pulling up of bolts of a head of cylinders
      Pulling up of bolts of inlet and final collectors
      Check of the sensor of provision of a butterfly valve
      Check of the moment of ignition
      Replacement of candles ignition/check of electric contacts
      Replacement of an element of the air filter
      Discharge of a sediment of the fuel filter of the diesel engine / replacement of the fuel filter
      Check of a maple belt / tension / replacement of a gear belt
      Visual check of system of production of the fulfilled gases
   + Box transfers/drive of wheels
   + Brakes/tires/wheels
   + Steering management / drive of forward wheels
   + Car electric equipment
   + Body / internal equipment
+ Petrol engines
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and system of steering
+ Brake system
+ Wheels and tires, body, coloring of the car, care of the car
+ System of electric equipment
+ Heater, system of lighting, devices
+ Governing bodies and methods of operation
+ Electric circuits

25215d41

Oil replacement

The following tools are necessary for replacement of oil:

  1. Viewing hole or the hydraulic elevator with support.
  2. The special device for weakening of an oil filter (nippers for an oil filter, a coupling tape key or HAZET 2172 adaptation).
  3. The set of face heads for weakening of a masloslivny stopper, and also capacity is 6 l for collecting oil.

The following wearing-out details are necessary:

  1. Laying for a masloslivny stopper (it is sometimes put to an oil filter).
  2. Boss of an oil filter. Upon purchase spare to specify model and year of release.
  3. Depending on the engine from 3 to 4 liters of engine oil. To use only the oils recommended by MAZDA see the Head the engine Lubrication system.

Amount of oil

Engine with replacement of the filter without replacement of the filter
E1, EZ, E5 3, 4 3, 2
VZ, V5, V6, BP (SOHC) 3, 0 2, 8
BP (DOHC) 3, 6 3, 4
PN (Diesel) 3, 6 3, 2

Replacement of oil should be made through each 10.000 km, at the diesel engine through each 5.000 km. At rare trips to make oil replacement once a year. At the same time the oil filter is at the same time replaced.

At severe conditions of operation, the movement by short pieces, frequent cold starts and strong dust content of streets, engine oil and an oil filter have to be replaced through shorter periods.

Old oil has to be handed over in special points. It is impossible to pour out old oil at all or to throw out with house garbage.

Discharge of engine oil

For the petrol engine

For the diesel engine

 PERFORMANCE ORDER

  1. To bring engine oil to the working temperature (min. +60 °C), for this purpose it is necessary to make a trip on 10 - 15 km.
  2. To lift the car in horizontal position.
  3. To substitute under the case pallet capacity for collecting oil.
  4. To unscrew a cover of a jellied opening.
  5. To turn out a bolt of a drain opening from below on the pallet of a case and to completely merge old oil.

If in oil traces of metal shaving and products of wear in a large number are visible, it indicates damages by a rust, for example, damages of the crankshaft or conrod bearings. In order to avoid the subsequent damages it is necessary to clear carefully after repair of the engine oil channels.

  1. To establish a bolt of a drain opening with new laying and to screw 40 Nanometers with effort.