Mazda 323

since 1985 release

Repair and operation of the car


Mazda 323

+ Introduction
- Petrol engines
   Specifications
   Removal and installation of the engine
   Removal and installation of a gear belt of VZ, V5, B6 (SOHC), BP engines (SOHC)
   Removal and installation of a gear belt (DOHC)
   Removal and installation of a head cylinders/replacement of laying of a head of cylinders
   Mechanism of the chain drive
   Removal and installation cam-shaft/adjustment of phases of gas distribution
   Removal and installation of the camshaft
   Cam-shaft/drive of the distributive mechanism
   Distributive shaft / drive of the distributive mechanism
   Removal and installation of camshafts
   Removal and installation of valves
   Replacement of maslootrazhatelny caps
   Check of the directing valves
   Processing of facets of saddles of valves in a head cylinders/processing of valves
   Grinding in of valves
   Check/adjustment of a gap of valves
   Check of a compression
   Removal and installation/tension of a maple belt
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and system of steering
+ Brake system
+ Wheels and tires, body, coloring of the car, care of the car
+ System of electric equipment
+ Heater, system of lighting, devices
+ Governing bodies and methods of operation
+ Electric circuits

25215d41

Removal and installation/tension of a maple belt

If the belt is established old maple, it always should be checked for wear and damages. If side surfaces are worn-out, there are cracks and gaps, the belt anyway should be replaced. At installation to watch that the belt correctly adjoined to all pulleys.

Maple belt of the generator and water pump

 PERFORMANCE ORDER

  1. To weaken the adjusting screw and a bolt of fastening.
  1. To incline the generator to the engine and to take off maple a belt.
  2. To impose a new belt and to tighten a nut and the lock screw.
  3. To check a tension between pulleys of the generator and water pump - an arrow-. At influence with a force of 100 N (10 kg) that approximately corresponds to pressing by a thumb to measure a belt deflection, the required values see in the table.
Designation of the engine deflection in mm
new belt the belt which was in the use
E1, EZ, E5 12 — 13 13 — 14
VZ, V5, V6 8 — 9 9 — 10
PN (Diesel) 9 — 10 10 — 10, 5
  1. To screw an adjusting bolt with effort of 25 Nanometers, a fastening bolt with effort of 50 Nanometers.

Maple belt of a servonasos (petrol engine)

 PERFORMANCE ORDER

  1. To weaken a lock nut and a bolt of fastening.
  1. To turn an adjusting bolt that it was possible to take off maple a belt. To take off maple a belt.
  2. To impose maple a belt to adjust a tension a bolt.
  3. To check a tension between pulleys of the crankshaft and oil pump of a servoupravleniye - an arrow-. At influence with a force of 100 N (10 kg) that approximately corresponds to pressing of a thumb, the new belt has to cave in on 8 - 9 mm, the belt which was in the use on 9 - 10 mm.
  4. To tighten a lock nut with effort of 25 Nanometers, a fastening bolt with effort of 45 Nanometers.

Maple belt of a servonasos and compressor of the conditioner (petrol engine)

 PERFORMANCE ORDER

  1. To weaken a lock nut and a bolt of fastening.
  1. To turn an adjusting bolt that it was possible to take off maple a belt. To take off a belt.
  2. To establish a new belt and to adjust a tension an adjusting bolt.
  3. To check a tension between pulleys of the crankshaft and oil pump of a servoupravleniye - an arrow-. At influence with a force of 100 N (10 kg) that approximately corresponds to pressing of a thumb, the new belt has to cave in on 8 - 9 mm, the belt which was in the use on 9 - 10 mm.
  4. To tighten a lock nut with effort of 25 Nanometers, a fastening bolt with effort of 45 Nanometers.