Mazda 323
+ Introduction
+ Petrol engines
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
- Suspension bracket and system of steering
Forward suspension bracket — the general information
Removal and installation of a depreciation rack
Dismantling of a depreciation rack / removal and installation of the shock-absorber / screw spring
Check of the shock-absorber
Removal and installation of the cross lever / replacement of a rubber support
Check/replacement of a support of the cross lever / rotary fist
Removal and installation of a power shaft
Removal and installation of an intermediate shaft
Check/dismantling of a driving shaft / replacement of cuffs
Bearing of a forward nave
Back suspension bracket
Removal and installation of a back depreciation rack
Dismantling of a back depreciation rack / removal and installation of the shock-absorber / screw spring
Cross levers / longitudinal lever / stabilizer
Check of the hug bearing
Removal and installation of the hug bearing
Adjustment of a side play of the hug bearing
Removal and installation of a nave
Steering
Removal and installation of a steering wheel
Removal and installation of a tip of steering draft
Removal and installation of a rubber cuff of the steering drive
Servoupravleniye pump
Angles of installation of wheels
Values for check of MAZDA 323
+ Brake system
+ Wheels and tires, body, coloring of the car, care of the car
+ System of electric equipment
+ Heater, system of lighting, devices
+ Governing bodies and methods of operation
+ Electric circuits
|
Removal and installation of a back depreciation rack Removal
|
|
- If necessary to remove a side upholstery in salon to reach the top bolts of a depreciation rack.
- To weaken nuts of wheels of the car standing on the earth.
- To change the provision of a disk of a wheel concerning a nave that the balanced wheel could be established in former situation.
- To lift a back part of the car.
- To remove a wheel.
|
|
- Only the four-wheel drive: To unscrew a bolt - And - which fixed the longitudinal lever on a suspension bracket beam. Then to weaken a bolt - In - without unscrewing. If is available, in addition to unscrew an air hose of system of adjustment of height of a road gleam on the shock-absorber from above.
|
- To remove a bracket-1-and to release a brake hose from the holder on a depreciation rack.
| Not to unscrew a brake hose. |
- To prop up a suspension bracket beam a support or the hydraulic elevator that it did not fall down when weakening a depreciation rack.
|
|
- To unscrew 2 nuts of a-2-depreciation rack on a suspension bracket beam, to remove bolts-3-.
|
- To unscrew 2 nuts on the top support of a depreciation rack and to take out a depreciation rack-5-.
- If necessary to sort a depreciation rack, see the Head Razbork of a back depreciation rack / removal and installation of the shock-absorber / a screw spring.
|
|
Installation
|
|
- To insert a depreciation rack, to tighten 2 top nuts with effort of 30 Nanometers.
- To insert 2 bolts of a depreciation rack on a beam in front back, to tighten nuts with effort of 110 Nanometers.
- To remove the elevator from under a beam.
- To strengthen a brake hose on a depreciation rack.
-
Only the four-wheel drive: To tighten bolts - And - and - In - with effort of 70 Nanometers. In the presence of system of adjustment of height of a road gleam to screw an air hose from above on the shock-absorber with effort of 20 Nanometers.
- To screw a wheel, at the same time considering a tag on a nave. To lower the car and to tighten nuts of wheels cross-wise with effort of 100 Nanometers.
- If it is removed, to establish an internal upholstery over a depreciation rack.
- To perform measurements of angles of installation of wheels.
|
|
|
On the homepage
|
