Mazda 323

since 1985 release

Repair and operation of the car

Values for check of MAZDA 323

When checking certain conditions have to be satisfied

Model	Parameter	Forward suspension bracket value for adjustment	Back suspension bracket value for adjustment
The forward drive with 8/85 on 9/89 g of the issue (except the diesel and "station wagon")	Convergence	2 ± Zmm (0 °12' ± 18 °)	0 ± 3 mm
	Disorder	0 ° 48' ± 45'	—
	Cross inclination of an axis of turn	12 ° 22'	—
	Выбег	10 mm	0 ° ± 45'
The forward drive from 10/89 g of the issue.	Convergence	2 ± 3 mm	2 ± 3 mm
	Disorder	- 0 ° 05' ± ^45'1	- 0 ° 20' ± 45'
	Выбег	2 ° 05' ± ^45'2	—
Diesels with 8/85 on 9/89 g of the issue.	Convergence	2 ± 3 mm	0 ± Zmm
	Disorder	0 ° 50' ± 30'	—
	Cross inclination	12 ° 20'	—
	Выбег	1 ° 35' ± 45' (10,5 mm)	—
The four-wheel drive to 9/90 g of the issue.	Convergence	2 ± 3 mm	0 ± 3 mm
	Disorder	without adjustment of height of a road gleam 1 ° ± 30'; with adjustment of height of a road gleam 0 ° 30' ± 30'	—
	Cross inclination of an axis of turn	without servoupravleniye 12 ° ^20'3 with a servoupravleniye 13 ° 00'	—
	Выбег	without adjustment of height of a road gleam 1 ° 45' ± 45'; with adjustment of height of a road gleam 2 ° 15' ± 45'
The four-wheel drive in 10/90 g of the issue.	Convergence	2 ± 3 mm	2 ± 3 mm
	Disorder	- 0 ° 45' ± 45'	0 ° 20' ± 45'
	Cross inclination of an axis of turn	12 ° 10'	—
	Выбег	2 ° 45' ± 45'	—

1 — the maximum difference between the right and left side 30B

2 — the maximum difference between the right and left side 40B

3 — "station wagon" with the four-wheel drive and adjustment of height of a road gleam: 12 ° 58'; without adjustment — 12 ° 05'

Adjustment of a convergence of forward wheels

PERFORMANCE ORDER

The provision of wheels at a positive convergence, looking from above. At the same time value - In - is in front.

Before adjustment of a convergence to weaken wire collars on rubber cuffs that they were not overwound. To weaken a lock-nut on a tip of steering draft and to adjust steering draft rotation of a hexagon.

At adjustment of a convergence it is necessary to consider that distribution of a convergence has to be identical at the left and on the right, it means that steering drafts have to be turned out at an identical size. The maximum difference on length: 3 mm.

To tighten lock-nuts of steering drafts with effort of 40 Nanometers. To fix a rubber cuff by a wire collar.

Adjustment of disorder of forward wheels

PERFORMANCE ORDER

If disorder of wheels lies out of admissible area, under certain circumstances it can be adjusted rotation of a plate of fastening of the shock-absorber. For this purpose to weaken 4 top nuts of fastening (to 9/89 g of the issue: 2 nuts) of the shock-absorber and to turn a fastening plate on 180 °, the represented tag will be outside. Disorder will change at the same time on +29'. To screw a fastening plate with the required inhaling moment, see the Head Podvesk and system of steering.

Adjustment of a convergence of back wheels

PERFORMANCE ORDER

Cars to 9/89 g of the issue and the station wagon model

The convergence of back wheels is regulated by rotation of two clowns on the back cross lever. After adjustment to measure distance from support of clowns to a wheel disk. To repeat measurement on other wheel. The deviation between the right and left parties can make at most 3 mm.

After adjustment to tighten eccentric bolts a hand and to lower the car on wheels. Only after that to tighten bolts finally with effort of 110 Nanometers.

Cars from 10/89 g of the issue, except the station wagon models

To adjust a convergence rotation of a carving bar on the back cross lever, having weakened previously a lock-nut. One turn of a carving changes a convergence to 11,3 mm. To evenly distribute adjustment between two wheels. After adjustment to tighten lock-nuts with effort of 60 Nanometers.

On the homepage