Mazda 323

since 1985 release

Repair and operation of the car



Mazda 323

+ Introduction
+ Petrol engines
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and system of steering
+ Brake system
- Wheels and tires, body, coloring of the car, care of the car
   The sizes of disks and tires/pressure in tires
   Designations of disks
   Designations of tires
   Replacement of wheels
   Rules of care of tires
   Balancing of wheels
   Antisliding chains
   Spare wheel
   Wear of tires
   Body
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of a front grille
   Removal and installation of side moldings
   Removal and installation of a forward wing
   Removal and installation/adjustment of a cowl
   Removal and installation/adjustment of a door of a back
   Removal and installation/adjustment of a door
   Upholstery door door/window regulator/glass
   Removal and installation of an upholstery of a door
   Removal and installation of a glass/window regulator of a forward door
   Door lock lock/handle/cylinder
   Back door lock / internal drive
   External mirror
   Removal and installation of glass of a mirror
   Panel of devices / average console
   Front seats
   Removal and installation of a back seat
   Back seat
   Coloring of the car
   Elimination of damages from stones
   Rikhtovka body/repair of rusty openings
   Preparation for painting
   Coloring
   Wash of the car
   Care of a varnish covering
   Protection of the bottom and preservation of cavities
   Care of an upholstery
+ System of electric equipment
+ Heater, system of lighting, devices
+ Governing bodies and methods of operation
+ Electric circuits


25215d41

Removal and installation of a forward wing

MAZDA 323 from 10/89 g of the issue.

Removal

 PERFORMANCE ORDER

  1. To change the provision of a disk of a wheel concerning a nave that the balanced wheel could be established in former situation.
  2. To weaken nuts of a wheel of the car standing on the earth.
  3. To lift a forward part of the car.
  4. To remove a wheel.
  5. To remove the forward index of turn-1-, see the Head Otopitel, system of lighting, devices.
  6. To remove a front grille-2-, and also an overlay of a lattice, the Head Kolesa and tires, a body, coloring of the car, care of the car.
  7. To remove a headlight-3-, the Head Otopitel, system of lighting, devices.
  8. To unscrew a mud-catcher-4-.
  9. To turn out bolts of a loker-5-from within, to wring out a loker from a wing and to take out.
  10. Because of protective mastic and a sealing tape the wing sits very strongly. The hair dryer reaching, at least, temperature of +450 °C is necessary for weakening of fastening of a wing. If there is no hair dryer, it is recommended to cut off protective mastic in junctions a knife.

To heat vinyl protective mastic of the bottom (material PVC) slightly and short time. PVC color should not change and should not be formed swellings. Otherwise there are evaporations hazardous to health, besides the hydrochloric acid leading to corrosion is formed.

  1. Carefully step by step to remove a wing.

Installation

 PERFORMANCE ORDER

  1. If necessary to paint a wing.
  2. To clear wing prileganiye surfaces, if necessary to align.
  3. To cover points of fastening of bolts of fastening of a wing in a wheel arch and a forward rack of a body with rust-preventing agent.
  4. To impose on prileganiye surfaces a standard tape for consolidation of wings.
  5. To establish, level and screw a wing. At the same time to watch a uniform gap between a cowl and a wing, and also a door and a wing.

Bolts of fastening (self-tapping screws) can drag on with effort of 10 Nanometers, i.e. it is absolutely easy.

  1. To apply mastic of protection of the bottom on wing inside.
  2. To condense a loker on a wing with sealant.
  3. To screw a mud-catcher.
  4. To establish a front grille and a decorative slip.
  5. To establish a headlight and the index of turn. To adjust headlights.
  6. To establish a wheel, considering a tag on a nave. To lower the car and to tighten wheel nuts cross-wise with effort of 100 Nanometers.